China Standard MARINE Galvanized Boat Trailer Axle 3500 lbs with 88 inch Hub Face a 3-axle vehicle

Product Description

Trailer axle measures 88″ from hub face to hub face and 82.5″ from spring center to spring center. Includes electric brake assemblies, hubs, drums, bearings, races, seals, and mounting hardware. E-Z Lube spindles for simple lubrication.

Factory replacement axle for SeaLion / TideWater Boat Trailers. Galvanized axle stock, includes pre-lubed zinc plated hubs with bearings, seals and caps with grease fittings. Does NOT come with lug nuts.

Hub Face = 88″
Spring Center = 82.5″
Hub Assembly = 5-on-4.5″ lug pattern
 

 

Features:

  • Square axle beam acts as part of your trailer’s suspension system
    • Replace an axle on your trailer
    • Fabricate a suspension to fit your application
  • High-strength steel construction
  • Bend in axle creates zero camber angle for even road-to-tread contact across the width of your trailer’s tires
    • Best for straight-line acceleration and steady, controlled towing
  • Underslung design – spring seats welded to underside of axle for mounting leaf springs
    • Low ride height makes it easier to load and unload your trailer
  • Straight, E-Z Lube spindles – no drop
    • Built-in grease zerks for simple lubrication
  • Spring seats and spindles are welded on
  • Electric brakes are easy to install – no actuator or hydraulic lines necessary
    • Adjuster plugs, mounting bolts, and hardware included
  • Cast iron hubs and drums are sturdy and durable
    • Bearings, races, seals, grease caps, wheel studs, lug nuts, and marine-grade wheel bearing grease included

 

Specs:
Axle Type: 2″ x 2″ x1/4″ thick Square – Galvanized
Load Rating: 3,500 lbs.
Track Length: 88″ Hub Face to Hub Face
Spring Center: 82.5″
Overall Length: 93″
Hub Type: 5 stud  x  5-on-4-1/2″ Bolt Circle, Zinc Plated
Spindle Size: inner bearing( # 68149)1-3/8″ x outer bearing(# 44649)1-1/16″ w/4-hole brake mounting flange 
Grease seal – 1.719 inches inner diameter

The spindle features a Stainless Steel Wear Sleeve to allow for long term protection for your seal surface. This ensures your seal surface won’t corrode away, meaning it will not pit or rust which would normally lead to letting water into your hub. Dexter Axle spindles also feature an E-Z Lube system, which allows easy greasing and regular maintenance of bearings. The grease travels through the center of the spindle and pushes out the old grease forward towards the front of the hub and out your dust cap, therefore replacing the old grease with new fresh grease. A castle nut and spindle washer are included on each spindle. These Hot-Dipped Galvanized Adjustable Spring Seats mean your axle will last longer, with no holes for saltwater and corrosion to hide. These Galvanized Adjustable Spring seats are included free of charge with the purchase of your axle.

PN Axle Type Rating Hub Face to Hub Face Spring Center To Spring Center Axle Size Finish Hub bolt pattern Overall Length
TAB030  3,500 lbs Trailer Axle Beam 3,500 lbs 88″ 82.5″ 2″ x 2″x 1/4″ Square Galvanized 5 on 4-1/2″ 93″

SELECTING THE PROPER TRAILER AXLE
When selecting an axle for your application remember to consider the following important specifications:

  • LOAD CAPACITY:  the load rating of the axle must support the maximum gross vehicle weight rating. For multiple axle trailers divide the GVWR by the number of axles to determine the minimum load capacity of each axle.

  • TRACK LENGTH:  measure your axle track length by determining the distance between the center of 1 tire to the center of the other tire. A more precise measurement can be made by measuring the distance from 1 ‘HUB FACE’ to the other. The hub face is also known as the mounting surface where the wheel studs are located.

  • SPRING CENTERS:  measure the distance from the center of 1 spring to the center of the other.
    NOTE: not required for replacement torsion axles

  • OVERALL LENGTH:  measure the distance from the very end of an axle’s spindle to the very end of the opposite spindle.

  • AXLE STYLE:  important when reusing old mounting hardware and also for proper tire clearance. Includes straight axles (round or square), drop axles with offset spindles, and torsion axles. Also consider spindle size when reusing existing hubs or drums.

  • AXLE CAMBER:  Most trailer axles are designed with a bend in the tube that will deflect when the load (weight of the trailer) is applied. This will theoretically bring the trailer wheel camber toward a 0 value that is the best setting for most trailer applications. This will allow the tires to wear evenly and allow the longest tread life. Camber can be affected by damage to the axle. For example, if the axle spindle is bent, this will usually cause a negative camber on that side which will cause excess tread wear on the inside of that tire.

     

 

 

HangZhou CZPT Machinery Co., Ltd is a professional manufacturer of trailer parts in HangZhou, ZHangZhoug Province, China since 2016.

 

We can produce many trailer parts & accessories as follows: Towbars, axles, brake drums, hubs, brake disc, bearings, springs and springs and suspension kits, couplings, mudguards, U-Bolts, Jockey Wheels, keel rollers and brackets, wobble roller, wheel spacer, equalizers and all accessories related to trailers.

If you can send me the drawings or specifications of the trailer parts, mechanical parts and wheels, we can give you our price.

Q1: Do you have factory?
A: Yes, we have our own factory, own engineers, we can meet custom’s unique requirement.

Q2: Can I have a sample order?
A: Yes, welcome sample order to test and check quality. Mixed samples are acceptable.

Q3: It’s OK to print my logo on your product?
A: Yes, we can according to your exact requirement.

Q4:How do you ship the goods and how long does it take arrive?
A: We usually shipped by DHL, UPS, FedEx, it usually takes 3-5 days to arrive. Airline and sea shipping also optional.

Q5: What is your advantages?
A: We are professional supplier for more than 10 years, we always put the quality and price at the first place. At the same time, our products are exported to various countries, we have full experience to solve thorny problems.

If you want to know about our products and us, welcome to enquiry and email me.thanks

1-Welcome OEM

  1. You can use your own brands or ours, if you use our brand, our professional team will help you design the packing.

2-Our service

  1. You inquiry related to our products or prices will be replied in 24 hours.
  2. Well-trained and experienced staffs to answer all your enquirys in fluent English.
  3. Protection of your sales area, ideas of your design and all your private information.
  4. We have a QC team, every product will be checked by them before packed.

3-Welcome to visit

  1. When you come to our company visit us, we will arrange a car for picking up and help you book hotel. If you want to visit the local scenic spot, our colleague will accompany you.

4-Warranty

  1. Customer should be provide the video and the pictures for the problem products.
  2. Products returned within the warranty period must bear product number & date code.

5-After service

  1. In production and after delivery, we will track on time and tell you goods situation.
  2. When the goods arrived, if you find any design and quality questions, or difference from your samples, please feel free to contact us, we will find the question and solve it with you.

/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Condition: New
Axle Number: 2
Application: Trailer
Certification: ASTM, CE, DIN, ISO
Material: Steel
Type: Front Axles
Samples:
US$ 1/Piece
1 Piece(Min.Order)

|
Request Sample

Customization:
Available

|

Customized Request

axle

What are the safety considerations when working with axles, especially during repairs?

Working with axles, especially during repairs, requires careful attention to safety to prevent accidents and injuries. Here are some important safety considerations to keep in mind when working with axles:

1. Personal Protective Equipment (PPE):

Wear appropriate personal protective equipment, including safety goggles, gloves, and steel-toed boots. PPE helps protect against potential hazards such as flying debris, sharp edges, and accidental contact with heavy components.

2. Vehicle Stability:

Ensure that the vehicle is on a stable and level surface before working on the axles. Engage the parking brake and use wheel chocks to prevent unintended vehicle movement. The stability of the vehicle is crucial to maintain a safe working environment.

3. Lifting and Support:

Use proper lifting equipment, such as hydraulic jacks or vehicle lifts, to raise the vehicle safely. Follow the manufacturer’s guidelines for lifting points and weight capacities. Once the vehicle is lifted, support it securely with jack stands or other appropriate supports to prevent it from falling or shifting during repairs.

4. Lockout/Tagout:

If the repair work involves disconnecting or removing any electrical or mechanical components that could cause the axle or wheels to move, follow lockout/tagout procedures. This involves locking and tagging out the power source, so it cannot be accidentally energized while work is being performed.

5. Proper Tools and Equipment:

Use the correct tools and equipment for the job. Using improper tools or makeshift methods can lead to accidents and damage to the axle or surrounding components. Follow the manufacturer’s instructions and recommended procedures for disassembling, repairing, and reassembling the axle.

6. Proper Torque and Tightening:

When reassembling the axle components, use a torque wrench to ensure that fasteners are tightened to the manufacturer’s specifications. Over-tightening or under-tightening can lead to component failure or damage. Follow the recommended torque values provided by the vehicle manufacturer.

7. Safe Handling of Heavy Components:

Axle components can be heavy and cumbersome. Use appropriate lifting techniques and equipment, such as hoists or lifting straps, to safely handle heavy axle parts. Avoid lifting heavy components alone whenever possible and ask for assistance when needed.

8. Proper Disposal of Fluids and Waste:

If the repair involves draining fluids from the axle, such as differential oil, ensure proper disposal according to local regulations. Use appropriate containers to collect and store fluids and dispose of them at authorized collection points.

9. Training and Experience:

Working with axles requires knowledge and experience. If you are unfamiliar with axle repairs, consider seeking assistance from a qualified mechanic or technician who has the necessary training and expertise. If you decide to perform the repairs yourself, ensure that you have the appropriate knowledge and skills to carry out the task safely.

By following these safety considerations, you can help minimize the risk of accidents, injuries, and damage when working with axles, ensuring a safe working environment for yourself and others involved in the repair process.

axle

What are the symptoms of a failing CV joint, and how does it relate to the axle?

A CV (constant velocity) joint is an essential component of the axle assembly in many vehicles. When a CV joint starts to fail, it can exhibit several symptoms that indicate potential problems. Here’s a detailed explanation of the symptoms of a failing CV joint and its relationship to the axle:

Symptoms of a Failing CV Joint:

1. Clicking or popping sounds: One of the most common signs of a failing CV joint is a clicking or popping sound when making turns. This noise usually occurs during tight turns and may indicate worn-out or damaged CV joint bearings.

2. Grease leakage: A failing CV joint may leak grease, which can be seen as dark-colored grease splattered around the CV joint or on the inside of the wheel. Grease leakage is typically caused by a cracked or damaged CV joint boot, which allows the lubricating grease to escape and contaminants to enter.

3. Excessive vibration: A worn-out CV joint can cause vibrations, especially during acceleration. The vibrations may be felt in the steering wheel, floorboards, or even the entire vehicle. These vibrations can become more noticeable as the CV joint deteriorates further.

4. Difficulty in turning: As the CV joint wears out, it may become difficult to turn the vehicle, especially at low speeds or when making sharp turns. This symptom is often accompanied by a clicking or popping sound.

5. Uneven tire wear: A failing CV joint can lead to uneven tire wear. If the CV joint is damaged or worn, it can cause the axle to wobble or vibrate, resulting in uneven tire tread wear. This can be observed by visually inspecting the tires and noticing uneven patterns of wear.

Relationship to the Axle:

The CV joint is an integral part of the axle assembly. It connects the transmission to the wheels and allows smooth power delivery to the wheels while accommodating the up-and-down motion of the suspension. The axle shaft is responsible for transmitting torque from the transmission to the CV joints and ultimately to the wheels.

Axles contain one or more CV joints, depending on the vehicle’s drivetrain configuration. In front-wheel drive vehicles, each front axle typically has two CV joints, one inner and one outer. Rear-wheel drive and all-wheel drive vehicles may have CV joints on both the front and rear axles.

The CV joint consists of a joint housing, bearings, and internal ball bearings or rollers. It is protected by a rubber or thermoplastic CV joint boot, which seals in the grease and protects the joint from contaminants. When the CV joint fails, it can affect the axle’s ability to transmit power smoothly and result in the symptoms mentioned above.

Regular inspection and maintenance of the CV joint and axle assembly are crucial to identify and address any issues promptly. If any of the symptoms mentioned earlier are observed, it is recommended to have the vehicle inspected by a qualified mechanic to determine the exact cause and perform necessary repairs or replacements.

axle

What are the factors to consider when choosing an axle for a custom-built vehicle?

Choosing the right axle for a custom-built vehicle is crucial for ensuring optimal performance, durability, and safety. Here are several key factors to consider when selecting an axle for a custom-built vehicle:

  1. Vehicle Type and Intended Use:
  2. Consider the type of vehicle you are building and its intended use. Factors such as vehicle weight, power output, terrain (on-road or off-road), towing capacity, and payload requirements will influence the axle selection. Off-road vehicles may require axles with higher strength and durability, while performance-oriented vehicles may benefit from axles that can handle increased power and torque.

  3. Axle Type:
  4. Choose the appropriate axle type based on your vehicle’s drivetrain configuration. Common axle types include solid axles (live axles) and independent axles. Solid axles are often used in heavy-duty applications and off-road vehicles due to their robustness and ability to handle high loads. Independent axles offer improved ride quality and handling characteristics but may have lower load-carrying capacities.

  5. Weight Capacity:
  6. Determine the required weight capacity of the axle based on the vehicle’s weight and intended payload. It’s crucial to select an axle that can handle the anticipated loads without exceeding its weight rating. Consider factors such as cargo, passengers, and accessories that may contribute to the overall weight.

  7. Axle Ratio:
  8. Choose an axle ratio that matches your vehicle’s powertrain and desired performance characteristics. The axle ratio affects the torque multiplication between the engine and wheels, influencing acceleration, towing capability, and fuel efficiency. Higher axle ratios provide more torque multiplication for improved low-end power but may sacrifice top-end speed.

  9. Braking System Compatibility:
  10. Ensure that the chosen axle is compatible with your vehicle’s braking system. Consider factors such as the axle’s mounting provisions for brake calipers, rotor size compatibility, and the need for an anti-lock braking system (ABS) if required.

  11. Suspension Compatibility:
  12. Consider the compatibility of the chosen axle with your vehicle’s suspension system. Factors such as axle mounting points, suspension geometry, and overall ride height should be taken into account. Ensure that the axle can be properly integrated with your chosen suspension components and that it provides sufficient ground clearance for your specific application.

  13. Aftermarket Support:
  14. Consider the availability of aftermarket support for the chosen axle. This includes access to replacement parts, upgrade options, and technical expertise. A robust aftermarket support network can be beneficial for future maintenance, repairs, and customization needs.

  15. Budget:
  16. Set a realistic budget for the axle selection, keeping in mind that high-performance or specialized axles may come at a higher cost. Balance your requirements with your budget to find the best axle option that meets your needs without exceeding your financial limitations.

When choosing an axle for a custom-built vehicle, it’s recommended to consult with knowledgeable professionals, experienced builders, or reputable axle manufacturers. They can provide valuable guidance, assist in understanding technical specifications, and help you select the most suitable axle for your specific custom vehicle project.

China Standard MARINE Galvanized Boat Trailer Axle 3500 lbs with 88 inch Hub Face   a 3-axle vehicleChina Standard MARINE Galvanized Boat Trailer Axle 3500 lbs with 88 inch Hub Face   a 3-axle vehicle
editor by CX 2024-03-09

Tags: hub